The One Ring
https://wap.one-ring.co.uk/

Bywater Mill WIP
https://wap.one-ring.co.uk/viewtopic.php?f=50&t=32484		 Page 1 of 2
Author:  Oldman Willow [ Wed Sep 28, 2016 9:18 pm ]
Post subject:  Bywater Mill WIP
I wanted to work on this project for a while. I decided to use the new rubble molds from Hirst Arts. I decided to use wood for the core of the building and Pink foam for the base.

Image

Image

Image

Image

I began by cutting three 4" by 4" and one 4" by6" end parts with 45% peaks I cut and two 2" by 8" wall sections.I used a hot glue gun to tack the parts so that I can make changes. The model is larger than I realised it would be.

Image

I did not notice that the water side roof line was different until I made the paper template. I will change it tomorrow.

Image

Image

You can see from the two reference photos why I need to change it.

Image

This is a photo of the recent changes to the mill. Some of the changes are interesting. I may use some of them.

I also have cast enough of the bridge mold #259 to start thinking about adding it to the wok schedule. I am using the arches for chimneys and may not have enough ready.

http://www.hirstarts.com/molds/moldsvill.html
Author:  Mapper [ Thu Sep 29, 2016 1:46 am ]
Post subject:  Re: Bywater Mill WIP
Looking forward to your progress on this. Not sure if I like the newer look of the mill. I like the roofline on the older better and the grasses vs the dock by the wheel. This flythrough might help you, though it shows the older look.

https://youtu.be/0rrolf6VM_U
Author:  Crucium Giger [ Thu Sep 29, 2016 9:56 am ]
Post subject:  Re: Bywater Mill WIP
As always I'm looking forward to seeing your work on this
Author:  Oldman Willow [ Thu Sep 29, 2016 2:07 pm ]
Post subject:  Re: Bywater Mill WIP
Mapper wrote:
Looking forward to your progress on this. Not sure if I like the newer look of the mill. I like the roofline on the older better and the grasses vs the dock by the wheel. This flythrough might help you, though it shows the older look.

https://youtu.be/0rrolf6VM_U


Wonderful video 8)

I can make the dock as a modular part. I may use the new back side window details on another building.

Crucium Giger wrote:
As always I'm looking forward to seeing your work on this


Thanks

I am going to cut more parts in a few minutes . I will post later when I have time for more photos and fitting.
Author:  Oldman Willow [ Thu Sep 29, 2016 4:39 pm ]
Post subject:  Re: Bywater Mill WIP
Image

Image

I cut the core parts from a old left over stair step. I did not take the extra 8 hours to glue the wood together and plane it to the correct thickness. I ran a 4" wide section through the Table saw and cut a 45 degree angles on both sides. I did the same with a 2" wide section. The roof thatch will be teddy bear fur so no need for hours of extra drying time that would be involved in a more precise cut. I used a miter saw for the 45 degree roof angles.

I want a very rigid core for this. There would bo reason not to use foam core board if you only have hand tools.Drywall filler and balsa wood would work fine for the details.I am using a very thin cast so I am going to over kill this project,at least until I have more experience with the new molds.
Author:  Oldman Willow [ Fri Sep 30, 2016 1:01 am ]
Post subject:  Re: Bywater Mill WIP
Image;

Image

I tacked the end on with hot glue. The cast boards are thin I may try a 4 bot cast or use basswood.

Image

The new photo has a better detail of the windows.
More overhang on the thatch will look better. I am glad I tacked it with hot glue.

Image

I think I will use two windows
Author:  Mapper [ Fri Sep 30, 2016 6:26 am ]
Post subject:  Re: Bywater Mill WIP
I was curious why the dock was added to the mill so I wrote Hobbiton Tours - here is their reply:

"As our maintenance department occasionally works out on the lake we decided to incorporate a dock for them to use along with function groups to access during dinners we serve in the mill."

And knowing is half the battle ☺
Author:  GreatKhanArtist [ Fri Sep 30, 2016 4:24 pm ]
Post subject:  Re: Bywater Mill WIP
I love it! I'm trying to save up for those new molds and that WIP pic just makes me want them more! :sad:
Author:  Quendil [ Fri Sep 30, 2016 6:58 pm ]
Post subject:  Re: Bywater Mill WIP
Wow looking great so far
Author:  Oldman Willow [ Fri Sep 30, 2016 9:19 pm ]
Post subject:  Re: Bywater Mill WIP
GreatKhanArtist wrote:
I love it! I'm trying to save up for those new molds and that WIP pic just makes me want them more! :sad:


I really like the new Hirst Arts molds. I decide to order Stucco Panel Mold #251 after I started working on the Mill model.

You might want to check out this site too. http://www.4botindustries.com/

I like the gothic sewer.

This is a room I have been working on using some of the 4 bot cavern floor molds mixed with Hirst Arts.

Image

The Dwarven Forge sewer is on the right side.
Author:  Oldman Willow [ Fri Sep 30, 2016 9:20 pm ]
Post subject:  Re: Bywater Mill WIP
Quendil wrote:
Wow looking great so far


Thanks
Author:  Oldman Willow [ Mon Oct 03, 2016 3:43 pm ]
Post subject:  Re: Bywater Mill WIP
Image

Image

Image

I was able to get more teddy bear fur at the fabric store. I will add a few small details. I am going to cut out the groundwork so I can begin the water side of the mill.
Author:  Oldman Willow [ Mon Oct 03, 2016 4:12 pm ]
Post subject:  Re: Bywater Mill WIP
Image

I realised I made the mill for human proportions when I saw this photo. :oops: I will start another wall section :roll:
Author:  Mapper [ Mon Oct 03, 2016 6:49 pm ]
Post subject:  Re: Bywater Mill WIP
Maybe he has been drinking ent draught. :-)
Author:  Oldman Willow [ Mon Oct 03, 2016 11:21 pm ]
Post subject:  Re: Bywater Mill WIP
Mapper wrote:
Maybe he has been drinking ent draught. :-)

:)

I cut a 1/2 inch off of the end parts and the walls. I will need to redo the details.

I am going to use the new stone pattern instead of the larger field stone.

Image

The stone wall ends at the door corner. I will trim the base. The wall also curves a bit. I may have to use a 4bot cast for that.
Author:  GreatKhanArtist [ Tue Oct 04, 2016 2:35 pm ]
Post subject:  Re: Bywater Mill WIP
I agree. The cobblestone looks out of place. I did check out the 4bot molds, some really cool stuff there! Do you have any photos of how the cavern castings stack? The website is woefully under-photo'd.

Also loving the cave/sewer you made. I'm going to have to copy that dwarven forge grate for my sewers. It's funny because I was thinking of doing a big round effluent grate in the wall before I saw the picture.
Author:  Oldman Willow [ Tue Oct 04, 2016 9:58 pm ]
Post subject:  Re: Bywater Mill WIP
Image

The 4 bot walls with a Griffin Tamer Dwarf gate.

Image

I made the walls so that the round column parts were on one side and the open wall parts were on the opposite side so that I could always fit them end to end.

Image

I made some risers to match the Dwarven Forge blocks.

Image

From the cavern floor mold.

Image

Some of the new stackable walls in the wall on center style.

Image

Blended with Hirst Arts and Dwarven Forge.

Image

The catacombs and walls.

Image

The 4 bot stalagmite cast and cavern floor tiles with some of my normal brown and under dark style DF tiles. You can see the 4 bot, blue gray, blends well with the DF tiles.

Image

I have only made a few cast of the new 4 bot village molds. I am going to use the wall on center on a few. I will make a few adapters for the normal wall on edge DF style. I think the wall on center style will work better for Massive Darkness and Black Plague and the new 4 edition D&D Middle Earth role play.
Author:  GreatKhanArtist [ Wed Oct 05, 2016 1:32 am ]
Post subject:  Re: Bywater Mill WIP
Nice. Thanks. Love the happy hobbit inn at the bottom.
Author:  Oldman Willow [ Wed Oct 12, 2016 2:29 pm ]
Post subject:  Re: Bywater Mill WIP
GreatKhanArtist wrote:
Nice. Thanks. Love the happy hobbit inn at the bottom.


I have been side tracked painting orc villagers for a role playing game. I found some more teddybear fur at JoAnn's Fabric.
Author:  Oldman Willow [ Thu Oct 13, 2016 5:22 pm ]
Post subject:  Re: Bywater Mill WIP
I was trapped in the diorama mode and forgot this is going to be gaming terrain. I decided to use the 4 bot windows instead of scratch built details no one can see. I also needed to leave room for bases on the model.

Image

1 1/2" should be enough for Most bases. I am going to use a stone floor pattern I have not cast yet instead of the tiles in the photo.

Image

I will decide if the mill wall will be 3/4" or 1" thick when the water wheel I ordered gets here. I may cut the bottom off of the PVC pipe water wheel or even have one laser cut.

Image

I will paint the major parts before I attach them. I need to decide how I want to do the bridge before I finalise the base.
Page 1 of 2 All times are UTC
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/