The One Ring
https://wap.one-ring.co.uk/

Is Buhrdur plastic or metal?
https://wap.one-ring.co.uk/viewtopic.php?f=30&t=25634		 Page 1 of 1
Author:  LordElrond [ Sat Mar 30, 2013 5:31 pm ]
Post subject:  Is Buhrdur plastic or metal?
As the title says...

Thanks, LordElrond
Author:  Rognarr [ Sat Mar 30, 2013 5:44 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
Metal (99% sure)
Author:  SouthernDunedain [ Sat Mar 30, 2013 5:45 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
definatley metal
Author:  LordElrond [ Sat Mar 30, 2013 5:49 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
Thanks guys.
Also, how easy is he to put together?
Author:  SouthernDunedain [ Sat Mar 30, 2013 5:53 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
lots of superglue and pinning.
Author:  LordElrond [ Sat Mar 30, 2013 5:56 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
Oh no.
How do I pin stuff?
Author:  SouthernDunedain [ Sat Mar 30, 2013 5:59 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
Hobby drill, paper clip. There should be tutorials on youtube.

You may get lucky and superglue will hold him together fine but pinning gives more strength.
Author:  Monotone_Matt [ Sat Mar 30, 2013 6:19 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
If you don't feel secure attempting to pin limbs, you can also try and apply a dash of greenstuff between the two parts and add superglue, which makes the greenstuff harden quicker!
Author:  LordElrond [ Sat Mar 30, 2013 6:44 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
Thanks SD, just watched a video on youtube about it.

@Matt: That'll be a good idea, or I could use all 3 just to be on the extremely safe side
Author:  Beowulf03809 [ Sat Mar 30, 2013 7:31 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
LordElrond wrote:
Thanks SD, just watched a video on youtube about it.

@Matt: That'll be a good idea, or I could use all 3 just to be on the extremely safe side


That's about what I did but for dual reasons. First, the GS w/ superglue will help hold better than the pin alone, but also you will need to fill the gaps of the join. I personally have more success putting the GS in place during the assembly and cleaning it up rather than finishing the assembly then trying to put the GS on to fill the gap. Just personal preference.
Author:  lostpict [ Sat Mar 30, 2013 7:39 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
He is metal and heavy. As such, even if you glue him securely he is subject to breakage without the pins during transports or a table top oops!

I would definitely pin his legs to torso and arms to torso. I have two of the older metal cave trolls and I tried Super glue alone, then Super glue with Greenstuff ,and finally pinned them after they broke twice previously. You can buy a pin vise and drills from GW or other hobby outfits. For the big monsters you can drill him with a hand drill or dremel, but you will eventually need a pin vise for more delicate minis (things like head or arm swaps). They way I do it is to drill a hole in each side. Test fit. Then glue the pin into the army. Squirt some super glue into the torso. Put a small blob of greenstuff on top and then jam it together. Use a hobby knife to scrape off any green stuff that is extruded from the joint. Last, I squirt some more superglue over the arm/torso joint to cover it up and then squirt it with Zap superglue accelerant.

OBTW, I just bought a Burdhur off e-bay and his is basically like the other trolls.

Lost Pict :sauron:

PS That sets my troll count to 10!
Author:  Grungehog [ Sat Mar 30, 2013 8:05 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
Mine is super glued and he's fine, never had anything go wrong with him, apart from paint chipping
Author:  Little_Odo [ Sun Mar 31, 2013 9:12 am ]
Post subject:  Re: Is Buhrdur plastic or metal?
Just bought him direct from GW - the figure is metal. Thanks for the tips on pinning - I will have to look into that when I put him together
Author:  RangerofTheNorth [ Sun Mar 31, 2013 9:58 pm ]
Post subject:  Re: Is Buhrdur plastic or metal?
Pin it! Tried all three ways he broke twice, pinned now and no issues
Author:  daersalon [ Mon Apr 01, 2013 1:16 am ]
Post subject:  Re: Is Buhrdur plastic or metal?
I have the Burduhr model, fully assembled, (yes indeed all metal)

He is heavy and the best option indeed is pinning. I usually use two part epoxy glue (e.g. Araldite in the UK), it doesn't take too long to set, and the metal-glue-metal bond is good. The advantage of the Epoxy glue is that it doesn't set 'hard' like superglue, there is some flexibility so any knocks or twists are absorbed better by the bond, and the join is far less likely to shear and need re-gluing.

Also as it oozes out it can fill any join and be trimmed with a craft knife.
Page 1 of 1 All times are UTC
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/