The One Ring
https://wap.one-ring.co.uk/

Alternatives to Green stuff?
https://wap.one-ring.co.uk/viewtopic.php?f=1&t=22837		 Page 1 of 1
Author:  samoscar09 [ Mon Apr 02, 2012 2:16 pm ]
Post subject:  Alternatives to Green stuff?
Hi wasn't sure where to post this
But does anyone have any alternatives to green stuff
Many thanks in advance
Author:  Dead Marsh Spectre [ Mon Apr 02, 2012 2:22 pm ]
Post subject:  Re: Alternatives to Green stuff?
Depends what your using it for, Gap filling try milliput
Author:  whafrog [ Mon Apr 02, 2012 4:28 pm ]
Post subject:  Re: Alternatives to Green stuff?
If you're looking to fill very thin lines, you might try the liquid green stuff GW sells.
Author:  Legolas31 [ Mon Apr 02, 2012 5:06 pm ]
Post subject:  Re: Alternatives to Green stuff?
I used to use blu tac before I found the wonders of GS
Author:  Jobu [ Mon Apr 02, 2012 5:29 pm ]
Post subject:  Re: Alternatives to Green stuff?
As others have mentioned, milliput is another two part epoxy that can be used, there are different grades though, stick with the yellow or white. There is also an epoxy made by gale force 9 which is grey and works well, dries harder than green stuff. These are good for adding sculpted features and gap filling.

There is modelers putty, which is usually white and comes in a tube, does shrink a bit upon drying. Testors makes a red putty which works better as it does not shrink as much. Neither of the puttys are good for sculpting. There is also green putty but I have never used it.

One could probably use some style of carpenters putty but I think it would depend on what you were doing. Watch out for some of the builders epoxies as they can cure very fast.
Author:  Dezartfox [ Mon Apr 02, 2012 6:39 pm ]
Post subject:  Re: Alternatives to Green stuff?
It completely depends what you use it for. I would always recommend Greenstuff over most other materials (don't even have to buy it from GW, look on heresy miniatures and sites like that, can get 36" of it quite cheap). Liquid Greenstuff is fantastic, brilliant for filling gaps.

If you're sculpting, then Milliput is ok for large areas, but can't really hold detail as it's rather crumbly when dry :) Procreate is another good sculpting material, I found it harder to mix so went back to the good old Greenstuff
Author:  theavenger001 [ Mon Apr 02, 2012 6:41 pm ]
Post subject:  Re: Alternatives to Green stuff?
There's also procreate.
Author:  Dagorlad [ Tue Apr 03, 2012 1:00 am ]
Post subject:  Re: Alternatives to Green stuff?
Ebob Miniatures sells green stuff and milliput - http://www.ebobminiatures.com/products/tools.htm

But I use ProCreate quite a bit, for gap filling mostly, but also for my feeble attempts at sculpting. I get it from Eureka Minis - http://eurekamin.com.au/product_info.ph ... ts_id=9904
Ebob sells sets of sculpting tools while Eureka sells a number of shaping tools - rubber tipped for smoothing out the putty (they are excellent).
Author:  Mighty.Uruk!!! [ Mon Apr 09, 2012 12:31 pm ]
Post subject:  Re: Alternatives to Green stuff?
procreate is a decent alternative but greenstuff is often the best there is
Author:  samoht [ Wed May 30, 2012 8:40 am ]
Post subject:  Re: Alternatives to Green stuff?
Pro create. I highly recommend it. It is better than greenstuff in my opinion.
Page 1 of 1 All times are UTC
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/